How to replace a Dell notebook keyboard
Written by Joe on Tuesday, April 22, 2008 – 11:23 pm -Today I replaced the keyboard on my sister’s Dell Inspiron 6000 laptop. She broke off one of the keys somehow, luckily I had it under warranty to get a free replacement keyboard shipped to me. The process is very simple and takes hardly any technical knowledge to do it.
These steps will work on ANY Dell notebook computer.
There is one variation for new models, but that will be made clear in it’s step.
Step 1 (the obvious step) - Obtain a new keyboard
Step 2 - Lay the screen flat so that you can remove the first part.
Step 3 - Insert a flat head screwdriver into a small slot on the right of the top casing piece. Don’t worry about damaging it, it is meant for a small flat head screwdriver to be inserted there without hurting the casing.
Step 4 - After popping the right side off with the screwdriver, just stick your finger under there and gently pull up, eventually popping off the middle and left side. Don’t worry, it may seem like you are going to break it but it will come off, just don’t use King Kong force.
Once it is completely off, remove the two screws holding down the existing keyboard. They are located on the top left and right of the keyboard, both black screws.
Step 5 - With the screws removed, place your hand on the top part of the keyboard and lift it up slightly. Then pull the keyboard towards the screen (away from you) until the bottom part comes out of the slots on the bottom. CAUTION: If you pull too hard and go 1/2 way across the room with it you could damage the connector on the motherboard.
Step 6 - Disconnect the keyboard from the motherboard.
***NOTE*** This is where some variation in models occurs. The older models, like the one in the picture, will have a tab for you to pull directly UP (not towards you) to remove the cable from the motherboard.
Newer models will have the cable snapped under a clip. To remove that, stick your finger between the clip and the cable where it connects and pull up to loosen the clip, then slide the wire out.
Step 7 - Grab the new keyboard. Replace the cable in the same but opposite way you removed the old one. If you have the cable like the one pictured, just simply push the connector into the one on the motherboard. If you have a newer model, slide the cable into the connector and push the clip back down to lock it in place.
Step 8 - Slide the bottom of the new keyboard into the slots while still holding the top part up a little bit. Replace the two screws you removed from the old keyboard.
Step 9 - Snap the top casing piece back into place. Start from the left hand side. You will see how you slide the left end into place then snap it down going from left to right until it’s all the way down.
Step 10 - VOILA! You’re done! Just make sure to turn it on and test that the keyboard works (notice the first and last steps are the easy ones!).
If you get stuck on any part you can contact me or post it here and I will respond.
Hope this was helpful!
Related Posts:
Tags: cable, connector, Dell, flat head screwdriver, Inspiron, keyboard, laptop, motherboard, notebook, remove, replacement, screw, warranty
Posted in Computer Tech |
May 12th, 2008 at 4:54 pm
[...] these instructions you’ll be able to remove and replace the keyboard on a Dell Inspiron 6000 series laptops. The [...]
May 12th, 2008 at 4:59 pm
Hi there,
Nice instructions. I linked to this guide from my site where I post all useful laptop repair guides.
August 7th, 2008 at 7:03 pm
Thank you very much! This is very helpful. It’s way cheaper to do it yourslef than to bring it to the shop.
August 14th, 2008 at 1:00 am
Hi,
Do you remember what model the replacement keyboard is? I have a Dell Inspiron 6000, and I also want to replace my keyboard.
Thanks!
August 14th, 2008 at 1:35 am
Thanks……..i just followed ur steps.
Please tell me the procedure to replace ram allso.
August 14th, 2008 at 2:59 am
Spazznie,
My 6000 was Part# H5639 - KYBD,87,US,ENG,S-PTG,STB
If you call Dell support they can get you in touch with a sales rep and get the correct part for you, just give them your service tag.
August 14th, 2008 at 3:05 am
Dr ravi Kumar Sivva,
To replace the ram, unscrew the main compartment on the bottom. It typically had the Windows serial key sticker on it with small little vents, right in the middle on the bottom.
Once you open that part, push the silver clips on the side of the RAM away from the RAM chip and pull the RAM out of the socket. It may seem tight but that is ok, just don’t use the force of an elephant.
To put new RAM in, be sure to line up the notch correctly and put it in the same way you took it out.
For picture detail, please see http://support.dell.com/support/edocs/systems/ins6000/en/sm/upgrades.htm
If you don’t have an Inspiron 6000, just go to http://support.dell.com and in the search bar put “replace ram your-model-here” hit search and then click Manuals on the left under Narrow Your Selection.
August 19th, 2008 at 10:50 am
Thanks Joe
August 29th, 2008 at 3:30 pm
Your directions are so esay to follow. However, I’m a little confused. I read another page that said the battery and hard drive had to be removed first , also one had to ground oneself while working on the replacement . Did you do any of that prep
before hand ? Lord ,I hope not. :-)
Thanks for your page , Joe.
August 30th, 2008 at 12:22 am
Jae D.,
Battery and hard drive do not need to be removed for the installation. However I do suggest removing the power adapter and battery just to be sure the laptop has no power to it since you will be disconnecting something, you don’t want to accidentally turn it on while you have it open.
As for grounding yourself, it is always a safe measure but if you are careful there is no need, you aren’t dealing with a part that is sensitive to electrical shock. I tend to stay on the safer side and ground myself when doing any internal computer work. Just wear shoes if on carpet and be sure to touch something metal before opening the laptop if you are worried.
Hope that helps.
August 30th, 2008 at 2:59 pm
Thank you ,Joe.THat’s a big help . Now all I
have to do is figure out which one is the battery . lol
Thanks again ,
Jae
August 30th, 2008 at 3:16 pm
The battery is typically the one that comes out by sliding some lock, the hard drive needs to get unscrewed and is about 1/2 the size.
September 29th, 2008 at 5:28 pm
Thanks man. I was jvst abovt to make a hvge mistake.
(where v = letter between y and i; hence reason for keyboard replacement)